Change or rekey · Royal
Lock Replacement & Upgrade in Royal
Someone tried the back door while you were away. The jamb is splintered around the strike, the bolt is bent, and the knob turns with a grinding feel.
Lock Replacement & Upgrade
In plain words
Lock replacement and upgrade is the service that takes tired or under-built door hardware off and puts hardware suited to the door in its place. It ranges from a like-for-like deadbolt on a back door to a complete refit of every entrance with heavier-grade locks, reinforced strikes and one key for the house. The locksmith first confirms that the person ordering the work has the right to change the lock, then examines the door, measures the existing preparation and recommends hardware that fits it cleanly. The visit ends with each lock tested from both sides, keys in your hand and the packaging and instructions left with you.
How the visit goesThe brass handleset has gone blotchy and green where the winter salt reaches it, and the coating on the deadbolt is lifting in flakes. It still locks, but it looks tired beside the fresh paint on the door.
Royal
How the visit goes
Measuring the existing preparation
Before any product is chosen the door is measured. Backset first, the distance from the door edge to the centre of the bore, which on most doors here is 60 or 70 millimetres. Then the cross-bore diameter, the edge-bore size, the shape of the latch faceplate, the door thickness and the handing. The strike cut-out and any glass, trim or storm door that limits where hardware can sit are noted too. These few numbers decide which locks will drop straight into the door and which would need a filler plate, an extension kit or fresh drilling, so they are written down before the catalogue is opened.
Mounting the cylinder and the interior side
The exterior housing goes on with its tailpiece passing through the slot in the bolt, oriented as the maker specifies so the keyway sits upright. The interior thumb-turn or rose is offered up and the two long mounting screws are drawn down evenly by hand until firm, not crushed; zinc housings distort and threads strip under a drill, and an over-tight rose makes a lever heavy forever. On thick doors, extension kits bring screws and spindle to length. A knob or lever set adds the latch spindle and the spring cage, and the handle is checked to return crisply to level before the trim is snugged.
Keys counted, named and planned
You receive the agreed number of keys, cut from the new pinning and tried in every door they should open, plus any code cards for a restricted system, which are what future copies are cut from. It is worth deciding on the spot who gets one and where the spare lives, ideally with a trusted neighbour or in a lockbox rather than in a drawer inside. If the house is now on a single key, retire every old key so none can be confused with the new one. A written list of which key does what goes in the home file.
Lock Replacement & Upgrade
In the van
- Knob or lever entry set
- Manufacturer-approved cylinder lubricant
- Boring jig and hole saws
- Key blanks and key cutter
- Reinforced strike plate and strike box
What affects the quote
Same fees day, night or weekend
1Grade of hardware
A light Grade 3 knob set, a residential deadbolt with a strong label rating and a Grade 1 commercial-style deadbolt are different products at different levels, and the quote follows the grade you choose for each door.
2Type of lock
A knob set, a lever, a deadbolt, a full handleset with deadbolt above, a patio door lock and a keypad or smart deadbolt each carry a different hardware cost and take different time to fit.
3Special-order hardware
Most standard locks come from the van. A specific style, an unusual finish or a restricted system may need ordering, which affects scheduling and is noted in the quote rather than discovered on the day.
Lock Replacement & Upgrade: questions
What is a reinforced strike, and is it worth adding?
A standard strike is a thin plate held by two short screws in the jamb, and the jamb is what splits when a door is forced. A reinforced strike or strike box is heavier and is fixed with long screws that pass through the jamb into the framing, spreading the load into the structure. It is one of the most effective upgrades on any exterior door and is usually fitted as part of a deadbolt replacement.
What does a higher grade of lock actually give me?
Grades follow ANSI/BHMA standards, with Grade 1 the highest and Grade 3 the lightest, and residential hardware carries a separate label that scores security, durability and finish. The grade reports how the lock performed on the standard's own operational, strength and security tests; a higher grade often comes with a longer bolt, a sturdier housing, pins that resist picking and a strike built to anchor into the framing, but those features are worth confirming on the specific model rather than assumed from the grade alone.
How long does a lock replacement take?
A straightforward like-for-like deadbolt or knob set on a standard door is often a matter of an hour or less including testing. Add time for a reinforced strike, for keying several locks alike and cutting keys, for a smart lock's setup and pairing, and for repairing a split jamb or adapting an older door. When several entrances are done together, the locksmith gives a realistic window before starting so you can plan the day.
Change or Rekey Locks
- Deadbolt InstallationSomeone tried the door last winter.
- Vintage Mortise Lock ServiceThe key turns freely in the round cylinder on the door, all the way around and back, without the…
- Smart Lock InstallationArthritis has made the small house key hard to grip and turn, especially with gloves on in January.
Lock Replacement & Upgrade near you
The lock services offered in Royal are grouped the way a door is used. Getting back in when you are locked out. Deciding who holds a working key. Upgrading the hardware so the door resists more than a casual try. Keeping commercial entrances working. Opening and maintaining safes. Each is described below.